Skip to product information
1 of 1

Sculpey Premo™ Honeycomb Necklace

Sculpey Premo™ Honeycomb Necklace

Designed by Amy Koranek
Read More
Hexagon cutters and Premo™ Butter are combined to design this asymmetric necklace. COMPLETION TIME: 90 Minutes to make, bake (bakes twice), and assemble Some additional time should be allowed for glue to dry
Read Less
  • Printed grid on paper to help line up design
  • Glass work surface
  • Heat set crystals (3)
  • Tweezers
  • E-6000 (GOOP) Silicone glue
  • Hexagon shaped gold tone connectors (2)
  • 4mm Gold tone jump rings (2)
  • 18” Gold tone chain with clasp
  • Wire cutters
  • Flat nose pliers
View full details
Project Instructions
    Getting Started:
Please make sure your work area is covered and you are not working on an unprotected surface. We recommend working on the Sculpey® Oven-Safe Work Mat, wax paper, metal baking sheet, or disposable foil. Uncured clay may damage unprotected furniture or finished surfaces. Be sure to cover your crafting area appropriately.

Start with clean hands, unwrap and knead clay until soft and smooth, or condition by running clay though a Pasta Machine. We recommend using a designated machine for clay purposes only. When working with multiple colors, clean hands with soap and water or baby wipes (we have found that baby wipes work best) before switching colors. Shape clay, pressing pieces firmly together. Wash hands after use.

Begin by preheating oven to 275 °F (130 °C). After you are done creating; for best results bake clay on an oven-proof surface such metal, aluminum foil, an index card or the Sculpey® Clay Mat at 275°F (130 °C) for 30 minutes per 1/4" (6 mm) thickness according to package directions. Oven safe glass or ceramic surfaces are also acceptable for baking; however please note that the baking times may take longer as the glass or ceramic surfaces take longer to heat up. For best baking results, use an oven thermometer. DO NOT USE MICROWAVE OVEN. DO NOT EXCEED THE ABOVE TEMPERATURE OR RECOMMENDED BAKING TIME.
Sheet 1/2 bar conditioned Premo™ Butter Yellow through the pasta machine on the second thickest setting.

Use the Hexagon cutters to cut out shapes from the sheet of clay. You will need a total of three large hexagons and six small hexagons.
Cut out 3 large hexagons and 6 small hexagons from clay
Place printed grid paper under a piece of glass. Lay out the asymmetric design on top of the glass using the grid below to make sure all the pieces are straight.

Notice that in my layout, several of the hexagon shapes are slightly overlapped. Be sure these overlapping pieces are connecting to each other well because this is what will hold the design together permanently.

Where the gold hexagon shaped connectors are placed is under one of the raised hexagons on each side. Press down gently to make an impression of the connector shape on the underside of the clay pieces.

Use the tip of the Small Etch ‘n Pearl to make radiating lines in some of the hexagons.
Lay out hexagons using printed grid paper under glass
Either the Knife Tool or the Small Etch ‘n Pearl are good for making the details.
Use tools to make lines and details
Gently press heat set crystals into the centers of each of the impressed pieces. Tweezers are useful for picking up and setting small crystals.

Bake the design on the glass following the baking instructions for Sculpey Premo™. Allow to cool completely before handling.
Press heat set crystals into place and bake
After baking, flip the design over. Add a small amount of E-6000 (or GOOP) to the area where the hexagon shaped connectors were imbedded.
Add glue where hexagon connectors were imbedded
Place the connectors back in their original position in the glue. You can prop the hexagon shape up so it doesn’t droop with some scrap clay as shown. Allow the glue to dry completely. My hexagon shaped connectors had little loops in them which I chose not to include in my design. So I turned the connectors so that the loops would be hidden on the back side.
After the glue has dried, add another of the small hexagon shapes over the glue area sandwiching the connector in place and hiding the glue.
After glue dries, add another small hexagon over glue area
This will make the back of the piece look neater. Bake again following the baking instructions for Sculpey Premo™.
Allow to cool completely before turning the piece over for assembly.
Allow glue to dry
Here is the layout for the necklace. Before assembling, cut the necklace chain in half directly at the midpoint using wire cutters.
Photo of necklace layout
Connect the two cut ends of the chain to the clay piece with jump rings using flat nose pliers.
Connect the chain with jump rings