Skip to product information
1 of 1

Sculpey Premo™ + Sculpey Souffle™ Elongated Teardrop Earrings

Sculpey Premo™ + Sculpey Souffle™ Elongated Teardrop Earrings

Designed by Amy Koranek
Read More
What says Summer more that blue skies and lemonade? These clever earrings, created with both Sculpey Premo and Souffle, sure evoke that “Summer Feeling”!
Read Less
  • Gold tone earring posts and backs (2)
  • 8 mm Gold tone jump rings (2)
  • Silicone glue or instant drying glue
  • Flat nose pliers
View full details
Project Instructions
    Getting Started:
Please make sure your work area is covered and you are not working on an unprotected surface. We recommend working on the Sculpey® Oven-Safe Work Mat, wax paper, metal baking sheet, or disposable foil. Uncured clay may damage unprotected furniture or finished surfaces. Be sure to cover your crafting area appropriately.

Start with clean hands, unwrap and knead clay until soft and smooth, or condition by running clay though a Pasta Machine. We recommend using a designated machine for clay purposes only. When working with multiple colors, clean hands with soap and water or baby wipes (we have found that baby wipes work best) before switching colors. Shape clay, pressing pieces firmly together. Wash hands after use.

Begin by preheating oven to 275 °F (130 °C). After you are done creating; for best results bake clay on an oven-proof surface such metal, aluminum foil, an index card or the Sculpey® Clay Mat at 275°F (130 °C) for 30 minutes per 1/4" (6 mm) thickness according to package directions. Oven safe glass or ceramic surfaces are also acceptable for baking; however please note that the baking times may take longer as the glass or ceramic surfaces take longer to heat up. For best baking results, use an oven thermometer. DO NOT USE MICROWAVE OVEN. DO NOT EXCEED THE ABOVE TEMPERATURE OR RECOMMENDED BAKING TIME.
From 1/8 bar of Ultramarine Blue Hue Premo™, make a long teardrop shape. Place it in the elongated teardrop cavity in the mold.
Place blue clay into mold
Flatten the teardrop of clay to fill the cavity.
Flatten clay into mold to fill it
Shave excess clay away with the Clay Blade so it is level in the cavity.
Shave excess clay away
Carefully remove the clay piece from the mold by gently flexing the mold. Follow Steps 2-5 to make a second elongated teardrop.
Flex mold to remove clay.
From Soufflé™ Canary, make four little lemon shapes and position them as shown so that the earrings are mirroring each other.
Make 4 little lemon shapes
Stipple the lemons with one of the Clay Tools.

For the lemon slices, make a small disc on the work surface in Premo™ Sunshine and flatten it really flat. The little disc should be about 1/4” wide.
In the center of the disk, flatten a very thin Premo™ White disc.
Then finally flatten a smaller disc of Premo™ Sunshine in the very center.
Cut the discs in half so that each one is half round.
Position two of the lemon slices on an earring and score little section lines with the Needle Tool.

Repeat this entire step to make another set of lemon slices for the second earring.
Make lemon slices
Next, make tiny White petals and arrange them in partial circles on each earring. Place a dot of Sunshine in the center of each one. Score little lines in the petals with the Knife Tool.
Make tiny white petals. Arrange and add Sunshine dot
Next, fill in the negative spaces with tiny leaves of Premo™ Green. Score texture in the leaves with the Needle Tool and add White dots as shown.

Roll the scraps of Ultramarine Blue Hue to a little sheet 1/8” thick. Cut out two squares using the 1/2” square mini geometric cutter. Turn them so they look like diamonds
Add green leaves. Use cutter to make earring tops
Poke holes in the bottom tip of the diamonds and in the top of the elongated teardrops.
Poke holes to attach earring pieces together
Bake the pieces following the baking instructions above. Allow the pieces to cool completely before handling. Lay the pieces out as shown for assembly.
Bake the clay
Use flat nose pliers to open the jump rings connecting the diamonds to the teardrops. Close the jump rings using pliers.
Use jump rings to assemble
Glue ear posts to the backs and allow to dry completely before handling.
Glue post backs into place