Skip to product information
1 of 1

Liquid Sculpey® Wanderlust Earrings

Liquid Sculpey® Wanderlust Earrings

Designed by Amy Koranek
Read More
Two great Liquid Sculpey® colors team up with a Blue Moon Studio™ UV Resin Earring Mold Kit to create a classic pair of earrings that are ready for all your travels – even if it is just to the grocery! TIME TO COMPLETE: 90 Minutes to make, bake, and assemble
Read Less
  • Paper towel
  • Silicone or paper baking liner
  • Blue Moon Studio™ UV Resin Craft Earring Shapes Silicone Mold Kit
  • Piñata Calabaza Orange Alcohol Ink
  • Small sharp scissors
  • 12 mm Gold tone jump rings (2)
  • 8 mm Gold tone jump rings (2)
  • Gold tone ear wires (2)
  • Flat nose pliers
View full details
Project Instructions
    Getting Started with Liquid Sculpey®:
Please make sure your work area is covered and you are not working on an unprotected surface. We recommend working on the Sculpey® Oven Safe Work Mat, wax paper, metal baking sheet, or disposable foil. Uncured Liquid Polymer Clay may damage unprotected furniture or finished surfaces. Be sure to cover your crafting area appropriately. - Stir Liquid Sculpey® completely. Thin with Sculpey® Liquid Clay Softener as needed - Wash hands after use (we have found that baby wipes work best)

  • It is important to use oven thermometer when you bake the liquids so that you can ensure your oven is at the correct temperature.
  • Do not microwave the liquids. They must be baked in a Preheated oven at 275 ºF (130 ºC) for liquid colors and 300 ºF (149 ºC) for Clear – Do not exceed baking temperatures.
  • If your piece is less than 1/4” bake for 15 minutes. For thicker pieces that are 1/4” or above bake for 30 minutes.
  • If your liquid project has become yellowed or discolored in the oven, when you remake it, tent it by placing either – folding an index card in half and placing your project under it or by using aluminum foil over your project.

Here’s a tip for baking perfectly in silicone molds. Dampen a dish towel with water and wring out as much of the water as you can. Fold the damp towel so that the molds can sit level on top of it. The damp towel will slow down the curing process so that the LS will cure evenly throughout and avoid warping.
While stirring the liquids, make sure that each liquid is relatively the same thickness. If the liquids are similar in thickness they will flow more nicely together. I do this by stirring and then lifting the stir stick out of the liquid to take note of how quickly the liquid drips back into the bottle. If some liquids are thicker than others, they can easily be thinned with Sculpey® Clay Softener and Thinner. Add a few drops of thinner at a time to the bottle and stir completely. Check by dipping and dripping again. Add more drops as needed.

Squirt some Pearl Liquid Sculpey® (LS) into the bottom of a small silicone or paper baking liner. You won’t need very much of the Pearl. Add a single drop of Calabaza Orange alcohol ink to the Pearl LS.
photo shows ink added to LS in bowl
Stir the color into the LS completely.
photo shows the LS stirred completely with the color added
Select the shape you want to fill in the silicone mold. I’m using the rounded squares. Squirt drops of Pearl from the bottle into the shape. We are not filling the mold at this time - just marking territories for each color.
photo shows dots of Pearl LS in molds
Next, drip little drops of Translucent Turquoise in the mold, leaving room for the orange.
photo shows small dots of Translucent Turquoise added to the molds next to the Pearl
Fill in between the Pearl and Translucent Turquoise with the Calabaza Orange/Pearl mixture. You can dip the tip of the Blunt Point tool into the mixture and drip the liquid in this way.

Next, add more drops of each color to fill the cavities just to level. Put more Pearl on top of Pearl. Put more Translucent Turquoise on top of Translucent Turquoise, and more Orange on top of Orange. By piling the colors on top of like colors, you make each color more opaque which will give a more deep color when baked.
photo shows the dots of color in the molds
Take the tip of the Needle Tool and dip it into one of the dots of color. Without lifting the tool, drag the tip through each color in a wave fashion to marble the colors.

Tap the mold on the work surface to release air bubbles.
photo shows the colors swilred together

Gently flex the mold to de-mold the baked pieces. You can trim the edges with sharp scissors if there are any rough spots. >
photo shows the baked pieces next to each other.
Here is the layout for the earring assembly.
photo shows layout for assembly
Use flat nose pliers to open and close jump rings to assemble the earrings as shown.
photo shows assembled earrings