Skip to product information
1 of 1

Sculpey Premo™ and Liquid Sculpey® Glass Bottom Bowl

Sculpey Premo™ and Liquid Sculpey® Glass Bottom Bowl

Designed by Amy Koranek
Read More
In this tutorial I give some suggestions regarding what colors of Premo™ to use for the rim of the bowl. But this is also a really great project if you have scraps of clay to use up. You can marble scraps together to create the beautiful and unique rim. COMPLETION TIME: 90 Minutes to make and bake (bakes twice)
Read Less
  • Small flat bottom glass or Pyrex dish 2.5” - 3” diameter
  • Gold glass filler micro chunks by Ashland
  • Paper towel
  • Heat gun

View full details
Project Instructions
Please make sure your work area is covered and you are not working on an unprotected surface. We recommend working on the Sculpey® Oven Safe Work Mat, wax paper, metal baking sheet, or disposable foil. Uncured Liquid Polymer Clay may damage unprotected furniture or finished surfaces. Be sure to cover your crafting area appropriately.

Getting Started with Premo Clay:
Start with clean hands, unwrap and knead clay until soft and smooth, or condition by running clay though a Pasta Machine. We recommend using a designated machine for clay purposes only. When working with multiple colors, clean hands with soap and water or baby wipes (we have found that baby wipes work best) before switching colors. Shape clay, pressing pieces firmly together. Wash hands after use.

Begin by preheating oven to 275 °F (130 °C). After you are done creating; for best results bake clay on an oven-proof surface such metal, aluminum foil, an index card or the Sculpey® Clay Mat at 275°F (130 °C) for 30 minutes per 1/4" (6 mm) thickness according to package directions. Oven safe glass or ceramic surfaces are also acceptable for baking; however please note that the baking times may take longer as the glass or ceramic surfaces take longer to heat up. For best baking results, use an oven thermometer. DO NOT USE MICROWAVE OVEN. DO NOT EXCEED THE ABOVE TEMPERATURE OR RECOMMENDED BAKING TIME.

Getting Started with Liquid Sculpey
Stir Liquid Sculpey® completely. Thin with Sculpey® Liquid Clay Softener as needed - Wash hands after use (we have found that baby wipes work best) .

• It is important to use oven thermometer when you bake the liquids so that you can ensure your oven is at the correct temperature. • Do not microwave the liquids. They must be baked in a Preheated oven at 275 ºF (130 ºC) for liquid colors and 300 ºF (149 ºC) for Clear – Do not exceed baking temperatures. • If your piece is less than 1/4” bake for 15 minutes. For thicker pieces that are 1/4” or above bake for 30 minutes. • If your liquid project has become yellowed or discolored in the oven, when you remake it, tent it by placing either – folding an index card in half and placing your project under it or by using aluminum foil over your project.
In the bottom of a small clean glass or Pyrex dish, place a thin layer of Clear Liquid Sculpey® (LS).
photo shows bowl with Clear LS in bottom
Sprinkle a layer of the broken glass filler over the top of the Clear LS.
photo shows as described
Sink the glass chips into the Clear LS with the tip of the Needle Tool. Wipe tools clean with paper towel.
photo shows as described
If necessary, add a little more Clear LS to have a thin coating over the top of the chips as well.
photo shows adding more Clear LS
Bake the little dish following the baking directions for Liquid Sculpey®. Allow the dish to cool completely.

Stick the tip of the Needle Tool in between the LS/glass disk and the side of the dish to break the seal between the two.

Gently use the tip of the Knife Tool to help loosen the LS/glass disk from the dish. Please be careful remembering that this is broken glass we are dealing with and it can be sharp.
photo shows baked LS disc removed from bowl
Roll a rope of 1/2 bar of Twinkle Twinkle, 1/4 bar of Ultramarine Blue, and 1/8 bar of 18K Gold. Make the ropes equal in length so that they vary in thickness.
photo shows as described
Bundle all three ropes together into one thick rope.
photo shows bundled rope
Roll the rope out long.
photo shows long rope
Now apply pressure to each end of the rope, one hand on each end, and then push toward the center using a rolling motion. This will make the rope shorter and thicker.

In this project we will spend some time rolling the rope thin and long and then rolling it back shorter and fatter. This will yield the sort of random galactic space pattern that we want.
photo shows as described
Roll the rope thin again. If the rope twists, untwist it because we aren’t going for stripes.
photo shows as described
Roll the rope fat again.
photo shows rope fat again
Roll the rope thin and untwist the stripes. See how the stripes are starting to get blurry along the edges? This is what we want!
photo shows stripes blurring
Roll the rope thick.
photo shows thick rope
Roll the rope thin untwisting the stripes.
photo shows roll the rope thin untwisting the stripes.
Roll the rope long one more time. Now, twist it just slightly to get the mottled look that you want.
photo shows mottled look
This time the rope should be rolled long enough to go all the way around the LS/glass disk. Trim the ends of the rope as needed and smooth the seam with your fingers.
photo shows rope around LS disc
Push the rope of clay into the edge of the glass bottom.
photo shows the edge of the glass bottom.
Turn the bottom of the dish over. There will be a thick rim of clay along the bottom of the glass piece.
photo shows thick rim
Push the bottom rim of clay flat to the glass piece.
photo shows rim pushed flat
Flip the bowl back over again. Pinch the edge of the clay upward thinning it and creating a nice rim.
photo shows top rim
Bake the dish following the baking instructions for Premo™ Sculpey® and allow to cool completely before handling. Look how lovely and clear the glass bottom is!
photo shows as described
To add even more shine, I added extra heat with a heat gun to both the Clear bottom and the Premo™ sides. Place the heat gun on high and move the heat back and forth across the piece until the clear bottom is shiny and the Premo™ has a nice sheen to it.
photo shows completed bowl