Skip to product information
1 of 1

Sculpey Soufflé™ Geometric Slab Votive

Sculpey Soufflé™ Geometric Slab Votive

Designed by Amy Koranek
Read More
This wonderful Sculpey Soufflé™ Geometric Slab Votive with the nickname "inchworm" will surprise and delight everyone that sees it! It is built around a cardboard form for shape and utilizes a clay "slab" for its graphic design. COMPLETION TIME: 90 Minutes to make and bake
Read Less
  • Paper tube from toilet tissue, paper towel, or wrapping paper
  • Packing tape
  • X-acto knife
View full details
Project Instructions
    Getting Started:
Please make sure your work area is covered and you are not working on an unprotected surface. We recommend working on the Sculpey® Oven-Safe Work Mat, wax paper, metal baking sheet, or disposable foil. Uncured clay may damage unprotected furniture or finished surfaces. Be sure to cover your crafting area appropriately.

Start with clean hands, unwrap and knead clay until soft and smooth, or condition by running clay though a Pasta Machine. We recommend using a designated machine for clay purposes only. When working with multiple colors, clean hands with soap and water or baby wipes (we have found that baby wipes work best) before switching colors. Shape clay, pressing pieces firmly together. Wash hands after use.

Begin by preheating oven to 275 °F (130 °C). After you are done creating; for best results bake clay on an oven-proof surface such metal, aluminum foil, an index card or the Sculpey® Clay Mat at 275°F (130 °C) for 30 minutes per 1/4" (6 mm) thickness according to package directions. Oven safe glass or ceramic surfaces are also acceptable for baking; however please note that the baking times may take longer as the glass or ceramic surfaces take longer to heat up. For best baking results, use an oven thermometer. DO NOT USE MICROWAVE OVEN. DO NOT EXCEED THE ABOVE TEMPERATURE OR RECOMMENDED BAKING TIME.
tape. Place packing tape across the bottom opening as well with the sticky side of the tape facing inside the tube. Trim around the edges of the bottom tape so it does not extend past the edges of the walls. My vessel form is 2-3/4” wide and 2-1/2” tall
photo shows the form with packing tape
Prepare the background clay. Condition and sheet both bars of Ivory Soufflé™ to a sheet 1/8” thick. At this point, just make sure there is enough clay to wrap around the vessel completely one time. Remove the clay sheet and lay it flat on the work surface. Set aside excess clay for now to be used on the bottom of the votive later.
photo shows clay sheet measuring around form
From 1/4 bar of Khaki Green Soufflé™ shape a little log 1/2” in diameter. Depending on the size of your vessel you may need to repeat this step later if you run out of inchworm shapes.
photo shows as described
Flatten the log with your fingertips to make it 3/4” wide and 1/8” thick.
photo shows flattened log
Use the Clay Blade to slice pieces from the log 1/16” thick.
photo shows as described
Flatten each piece by pinching between your thumb and forefinger.
photo shows as described
Bend the little Khaki Green pieces slightly so they kind of look like inchworms and press them as flatly as possible onto the Ivory background.
photo shows adding designs to background
Continue covering the background with the little inchworm shaped graphics in a random pattern. I know that my clay sheet is slightly wider than my vessel form is tall, so I’m not concerned with getting the pattern completely to the edges because I know those will be trimmed.
photo shows filled background
Roll the inchworm graphics into the background with the Acrylic Clay Roller.
photo shows as described
Use the Large Etch ‘n Pearl to punch holes in the design for candle ventilation. Push the pearl end of the tool into the clay as deeply as possible - preferably all the way through to the work surface. Spin the tool against the work surface to cut completely through the clay. When you lift the tool out of the clay the little circle will come with it. Press the end of the tool into some Ivory scrap clay to release the circle from the tool.
photo shows using Etch n Pearl to make holes in pattern
Take excess Ivory clay from Step 3 and sheet it to 1/8” thick. Position the votive form in the center of the sheet of clay. The non-sticky side of the packing tape across the bottom of the votive should be in close contact with the clay sheet.
photo shows building/adding bottom to votive
Carefully trim out a piece of clay to fit the bottom of the vessel. Carefully turn the vessel upside down and smooth the cut edge of the clay with your fingertips. Make sure the clay is sitting nice and flat on top of the packing tape.
photo shows sealing bottom to sides
Wrap the patterned sheet around the outside of the vessel form.
photo shows as described
Trim the sheet so that the two ends butt right up next to each other. Smooth the seam with your fingertips to blend it together.
photo shows smoothing seam
Take a few extra inchworm graphics and position them across the seam to make sure the pattern continues smoothly. Roll the entire vessel on its side on the work surface to make sure everything is nice and smooth.
photo shows as described
Make sure the sides of the vessel are in really good contact with the bottom piece of clay. Trim away excess clay around the bottom with the Clay Blade.
photo shows as described
Smooth seams around the bottom edge with your fingertips.
photo shows smoothing seams with fingertip
Stand the votive upright. Trim the top edge along the cardboard insert by pushing the corner of the blade through the clay.
photo shows trimming top edge
If the little holes got distorted during the move from flat to round, don’t worry, those will clean up easily after baking.
photo shows using tool to adjust the little holes
Bake the votive following the baking instructions for Sculpey Soufflé™. If there was packing tape that extended past the top edge of the votive, it may have shrunk during baking, this is perfectly fine.
photo shows as described
Allow the votive to cool completely before handling. If you try to remove the clay from the cardboard before it is cool, it may break.

Insert the tip of the Knife Tool between the clay and the cardboard, but only about 1/4” deep. Slide the tip of the Knife Tool all the way around loosening the top edge of the clay from the top edge of the cardboard. Once you have gone all the way around, you can push the knife in another 1/4” deeper and repeat. Keep pushing the knife in deeper until the clay is completely separated from the vessel form.
photo shows sliding knife tip around top
Carefully push the clay form off of the cardboard form. You may wish to use the form again on a future project.

Inspect the little holes. They can easily be cleaned up with the tip of an X-acto knife.
photo shows pushing off form
Add a small candle that has a protective metal or glass housing.
photo shows completed votive