Free Shipping on all Orders Over $49.99 in the Contiguous United States! We do not ship internationally or to PO boxes.

Liquid Sculpey® Glitter & Shine Earrings

Designed by Amy Koranek
Create a clever pair of earrings with lots of personality, sparkle and shine in just an hour with this easy project.

60 Minutes to make and bake
Save To Create Later
Grouped product items
Product ImageProduct Name Qty
Liquid Sculpey® Clear 2 oz
Sculpey Tools™ Clay Tool Starter Set
Glamour photo for the Sculpey Glitter and Shine Earrings
Click image to open expanded view
Glamour photo for the Sculpey Glitter and Shine Earrings
  • Paper towel
  • UV Resin Craft earring shapes silicone mold
  • Iridescent foil flakes
  • Bright color super fine glitter
  • Tweezers
  • Heat gun - optional
  • 8 mm Silver toned jump rings (2)
  • 4 mm Silvertoned jump rings (2)
  • Silver toned ear wires (2)
  • Flat nose pliers

Project Instructions

    Getting Started with Liquid Sculpey®:
Please make sure your work area is covered and you are not working on an unprotected surface. We recommend working on the Sculpey® Oven Safe Work Mat, wax paper, metal baking sheet, or disposable foil. Uncured Liquid Polymer Clay may damage unprotected furniture or finished surfaces. Be sure to cover your crafting area appropriately. - Stir Liquid Sculpey® completely. Thin with Sculpey® Liquid Clay Softener as needed - Wash hands after use (we have found that baby wipes work best)

  • -It is important to use oven thermometer when you bake the liquids so that you can ensure your oven is at the correct temperature.
  • -Do not microwave the liquids. They must be baked in a Preheated oven at 275 ºF (130 ºC) for liquid colors and 300 ºF (149 ºC) for Clear – Do not exceed baking temperatures.
  • -If your piece is less than 1/4” bake for 15 minutes. For thicker pieces that are 1/4” or above bake for 30 minutes.
  • -If your liquid project has become yellowed or discolored in the oven, when you remake it, tent it by placing either – folding an index card in half and placing your project under it by using aluminum foil over your project.

Here’s a tip for baking perfectly in silicone molds. Dampen a dish towel with water and wring out as much of the water as you can. Fold the damp towel so that the molds can sit level on top of it. The damp towel will slow down the curing process so that the LS will cure evenly throughout and avoid warping.
Put a thin layer of Clear Liquid Sculpey® (LS) in the bottom of the rounded corners squares wells. Don’t fill the mold to level yet so that you have plenty of room to add the glitters.
photo shows adding thin layer
Using tweezers, add some bits of iridescent foil to the horizontal center of each of the rounded corner squares.
photo shows adding foil bits
Add fine glitter above and below the foils making a rainbow. My iridescent foil has a blue tint to it, so I added the glitters working out from the blue. Yellow, bright green and green above the blue; and purple, pink, and orange below.
photo shows glitter added as described
Add more Clear LS to fill the mold to level. Tap the mold on the work surface to release air bubbles.
photo shows more Clear LS added to level
Bake following the baking instructions for Liquid Sculpey®.
NOTE: Some artists prefer to use a heat gun to heat the surface of the baked LS to create a shine to the surface. Preheat the heat gun and keep it moving across the clay until you see the shine appear. Allow to cool completely.
photo shows mold ready to bake
After the mold is completely cool, flex it to release the baked pieces. Use flat nose pliers to add jump rings and ear wires to finish the earrings.
photo shows completed earrings