Liquid Sculpey Personalized Lacy Holiday Stocking

Step 1:

Please make sure your work area is covered and you are not working on an unprotected surface. We recommend working on the Sculpey® Work ‘n Bake Clay Mat, wax paper, metal baking sheet, or disposable foil. Uncured Liquid Bakable Medium may damage unprotected furniture or finished surfaces. Be sure to cover your crafting area appropriately.
- Gently stir the bottle of liquid bakeable medium. - Wash hands after use (we have found that baby wipes work best) Baking
- It is important to use oven thermometer when you bake the liquids so that you can ensure your oven is at the correct temperature. - Do not microwave the liquids. They must be baked in a Preheated oven at 300 ºF (149 ºC) for liquid colors and 325 ºF (163 ºC) for Clear – Do not exceed baking temperatures. - If you are using the liquids as a glaze or in thin pieces less than ¼ inch bake for 15 minutes. For thicker pieces that are ¼ or above bake for 30 minutes. - If you are baking on a ceramic tile then you will also need to bake at 30 minutes since it will take longer for the tile to heat up. This will ensure the proper fusing of the liquid material. - When baking these liquids you may experience some vapors or a slight odor. This is not harmful and will not affect your creation. - If your liquid project has become yellowed or discolored in the oven, when you remake it, tent it by placing either – folding an index card in half and placing your project under it or by using aluminum foil over your project.

Step 2:

Fill the Mandala mold with Silver Liquid Sculpey (LS). You will need all of the larger sized mandalas to complete your stocking design. Squeegee off excess LS and return it to the bottle. Bake the mold following the baking instructions for LS. When the mold is completely cool, gently peel the mandalas out by flexing the mold. Next, mix Silver LS and Blue LS 1:1 in a paper cupcake liner (supported by a cupcake pan) or in a silicone cupcake liner. Fill the mold and squeegee off excess. Bake the mold following the baking instructions for LS.

Step 3:

When the mold is completely cool, gently peel the mandalas out by flexing the mold.

Step 4:

To make more pieces, I used sharp scissors to cut my mandalas. I cut the largest ones as shown turning each large mandala into two.

Step 5:

I cut the medium mandalas as shown.

Step 6:

Print the name that you want to place on the stocking onto copier paper. I chose this font because the letters are fairly open and I knew I could easily hook them together to make them cursive. I prefer to work with cursive lettering when I make LS words because the letters are all hooked together giving me fewer individual pieces to handle.

Step 7:

Place a piece of glass over the name. The glass should be clean, clear, and flat. My glass is an old glass turntable from a microwave that I keep in my studio for just this purpose. It is textured slightly on the back, but the top is completely smooth. Those little odd triangles you see in the glass are just the turntable feet which are on the underside so they do not affect my writing. Carefully trace the letters onto the glass with Silver LS. Bake the name as quickly as possible so that the LS does not spread.

Step 8:

When the glass is completely cool, you can use a sharp craft knife to trim and sharpen the edges of the letters if you like. I trimmed the centers of the “A” and I also made the little notches at the tops of the “n’s” more prominent.

Step 9:

Carefully peel the name from the glass by lifting it with your fingernail. Next, lay out your mandalas and your name to see how it looks on the cuff of your stocking. My stocking is white so I had to really make sure my hands and even my molded pieces were really clean before auditioning them on the design.

Step 10:

Measure and cut a piece of paper so that it represents the area and shape that you want your finished design to take up on the stocking cuff. Lay this piece of paper under the glass. Lay out the mandalas on top of the glass but staying within the area represented by the paper.

Step 11:

Using the small Style ‘n Detail ball stylus, drip little dots of Clear LS into areas where the mandalas overlap each other. This will act as the glue that holds the design all together. Make sure that every mandala is connected to the one next to it so that the design becomes one piece.

Step 12:

Next, on the back side of the name, place very small amounts of Clear LS

Step 13:

Carefully flip the name over, positioning it on top of the mandalas

Step 14:

Bake the name and the mandalas again, to set the Clear LS that will hook everything together. When the piece is completely cool, carefully peel it off of the glass.

Step 15:

Place the piece on the stocking to see how it looks. I felt that my initial design didn’t fill up the cuff area the way that I wanted it too, so I added a few more little mandalas to the left and right edges. I placed the design back onto the glass, and used more Clear LS to add the new mandalas in place, then baked again. Glue the design permanently to the stocking cuff with little dots of clear drying craft glue applied to the back of the design. Allow the glue to dry completely before handling the stocking.

Step 16:

Next, add some dangling mandalas like snowflakes falling from the cuff. Mold more Silver LS mandalas and more Silver/Blue mandalas. Allow them to cool completely before peeling them from the mold. Then add even more Blue LS to the leftover tinted Silver/Blue so you have a deeper color still. Make a few small mandalas in the deep Blue and bake them too. Hang them from the cuff of the stocking by stringing them on clear bead floss. Then secure them by adding a dot of clear drying craft glue to the bottom mandala attaching it to the floss. Allow the glue to dry completely before handling.