| 
Coal
The Coal pieces can be used for mouth, nose, or eye decorations for your snowman.
What you'll need:
- 2oz. of Sculpey III Black
- Sculpey Clay Tool with flat end
Directions
1. Divide your black into 3 pieces. One piece will be 1/2 of the black and the other two pieces should be 1/4 each. Roll each up into a ball and then flatten them. They should not be perfect circles because, remember, this is supposed to look like coal.
2. Using the clay tool, make random dents all over the top of your coal pieces. See the instructions for placing a screw in the back before baking.
Cheeks
What you'll need:
- 2oz. of Sculpey III Ballerina
1. Divide the Ballerina in half. Roll each half into a ball and flatten each ball into a cheek.
2. See the instructions for placing a screw in the back before baking.
Eyes
What you'll need:
- 2oz. of Sculpey III Black and White
- 1oz. French Blue
Directions
1. Slice a very small amount of black off and set it aside. Divide the rest of the black into two equal pieces. Shape these into an egg shape. Flatten each shape, stretching and shaping it into a flat oval.
2. Slice a very small amount of white off and set it aside. Divide the rest of the white into two equal pieces. Shape these into an egg shape. Flatten each shape, stretching and shaping it into a flat oval. Place them on top of the black ovals.
3. Divide 1 oz. of French Blue in half. Flatten each half into the bottom of each eye for the iris. Using the black that you set aside in step 1, place a smaller black circle into the center of each iris. Using the white that you set aside in step 2, place a little white circle off center on each pupil.
4. See the instructions for placing a screw in the back before baking.
Carrot Nose
What you'll need:
- 2oz. or 4 oz. of Sculpey III Just Orange
- Sculpey Clay tool with a flat edge
Directions
1. 2 oz. will make a nose that is about 3" long. 4 oz. will make a nose that is 3-1/2" to 4" long. Shape the orange into a thick carrot shape that is flat on the bottom.
2. Use the tool to indent marks in the sides of the carrot.
3. See the instructions for placing a screw in the back before baking.
Buttons
Snowflake Button
What you'll need:
- 1oz. of Sculpey III French Blue, a scrap of White
Directions
1. Make a ball out of the blue and then flatten it into a large disk. Make a six pointed snowflake in the middle with coils of white.
 
2. See the instructions for placing a screw in the back before baking.
Purple Square Button
What you'll need:
- 1oz. of Sculpey III Violet
Directions
1. Make a ball out of the violet and then flatten it into a large square. Trim the edges to make a "perfect" square.
2. Roll up the violet scraps that were trimmed off. Roll into a long coil. Border each edge of the button with the rope. Trim it to fit.
 
3. Poke four large holes in the button with the clay tool. Poke each hole all the way through in one direction and then go back through from the other direction.
4. See the instructions for placing a screw in the back before baking.
Green Round Button
What you'll need:
- 1oz. of Sculpey III Green
Directions
1. Make a ball out of the Green and then flatten it into a large circle.
2. Poke four large holes in the button with the clay tool. Poke each hole all the way through in one direction and then go back through from the other direction.
3. See the instructions for placing a screw in the back before baking.
Pink Round Button
What you'll need:
Directions
1. Make a ball out of the Pink and then flatten it into a large circle. Using a circle cutter smaller than circle press firmly making an indent but not cutting completely through the clay.
2. Poke two large holes in the button with the clay tool. Poke each hole all the way through in one direction and then go back through from the other direction.
 
3. See the instructions for placing a screw in the back before baking.
Instructions for inserting screws into snowman pieces
In order to make your snowman decorations attach to your snowman, you'll need to insert something into the back of each piece before baking. A 2" to 3" screw will work well and hold up for a long time.
1. After your pieces are constructed, turn them over. Gently press the head of the screw into the middle of the back of each piece.
 
2. You may even want to reinforce the screw by putting a piece of scrap clay all the way around it. It doesn't matter what color you use, this part will not be seen. When the screws are inserted and secure, bake the entire piece. You may bake the pieces up side down with the screws pointing up. You'll want to line your baking sheet with a piece of white paper just to make sure nothing gets picked up from the pan onto the front of your decorations. Bake at 275 for 15 minutes.
|
